[mythtv-users] PVR150 card on Mandriva 2005LE

[Greg Cole]

Hello all...

I've recently obtained a PVR150 card for my PC.... and its not working.
My setup is Mandriva 2005LE with kernel 2.6.11-6mdk.  
I used the mandriva distribution RPM to install IVTV, myth, xawtv, etc. etc.
All seem to find the devices just fine - but alas - no picture :-(

Any help with the following dmesg output would be appreciated.
Especially where these messages are coming from:

	ivtv: i2c client addr: 0x40 not found!
	ivtv: i2c client addr: 0x21 not found!

Thanks,
Greg


ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.2.0 (rc3f) loading
ivtv: Linux version: 2.6.11-6mdk 686 gcc-3.4
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Unknown card: vendor/device: 4444/0016, subsystem vendor/device: 
0070/8003
ivtv: Defaulting to WinTV PVR 250 card
ivtv: Please mail the vendor/device and subsystem vendor/device IDs and what 
kind of
ivtv: card you have to the ivtv-devel mailinglist: 
http://sourceforge.net/projects/ivtv
ivtv: Prefix your subject line with [UNKNOWN CARD].
ivtv: Found an iTVC16 based chip
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x01e0 vendor: 0x10de
ivtv: i2c attach [client=tveeprom,ok]
tveeprom: Hauppauge: model = 26032, rev = C199, serial# = 8004990
tveeprom: tuner = <unknown> (idx = 99, type = 0)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = TDA9850 (type = 3)
ivtv: Tuner Type 0, Tuner formats 0x00001000, Radio: yes, Model 0x008d1659, 
Revision 0xe0f26760
ivtv: NTSC tuner detected
ivtv: Radio detected
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
msp3400: error while reading chip version
ivtv: Encoder revision: 0x02050032
ivtv: Encoder Firmware is buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 250 card with 5 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers  4194304 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers  2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 455 4608 byte buffers  2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Setting Tuner 0
tuner: type set to 0 (Temic PAL (4002 FH5)) by ivtv i2c driver #0
ivtv: Setting audio matrix to input 3, output 1
ivtv: i2c client addr: 0x40 not found!
ivtv: Switching standard to NTSC.
ivtv: i2c client addr: 0x40 not found!
ivtv: i2c client addr: 0x21 not found!
ivtv: Initialized WinTV PVR 250, card #0
ivtv: ====================  END INIT IVTV  ====================
ivtv: ivtv_enc_thread: pid = 4412, itv = 0xe0f26760


-- 
Greg Cole
gregjcole at comcast.net