[mythtv-users] Problems starting ivtv (interrupt conflict?)

[Vassilis]

After a number of problems (interrupt issues) I was
able to load the ivtv module without any major issues.

However when I try to do a test capture all I get is a
zero byte file, not even static. I have the card set
to capture from the tuner. I am not sure to which
channel I am tunned, but in any case I would expect to
get static.

Log attached bellow, any help is appreciated!!!

Thanks,
Vassilis


ivtv: ==================== START INIT IVTV
====================
ivtv: version 0.2.0 (rc3j) loading
ivtv: Linux version: 2.6.12-1.1447_FC4 686 REGPARM
4KSTACKS gcc-4.0
ivtv: In case of problems please include the debug
info
ivtv: between the START INIT IVTV and END INIT IVTV
lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 250 card
ivtv: Found an iTVC16 based chip
PCI: Assigned IRQ 5 for device 0000:00:09.0
ivtv: XXX PCI device: 0x1647 vendor: 0x10b9
tveeprom: Hauppauge: model = 32031, rev = B110,
serial# = 6148272
tveeprom: tuner = Philips FI1236 MK2 (idx = 10, type =
2)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 =
0x00001000)
tveeprom: audio_processor = MSP3435 (type = 10)
ivtv: i2c attach [client=tveeprom,ok]
ivtv: i2c attach [client=(tuner unset),ok]
tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
saa7115: starting probe for adapter ivtv i2c driver #0
(0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115,ok]
saa7115: status: (1E) 0x48, (1F) 0xc0
msp34xx: ivtv version
msp34xx: init: chip=MSP3435G-B6, has NICAM support,
simple (D) mode, simpler (G) no-thread mode
msp34xx: $Id$ compiled on: Aug 30 2005 19:51:23
ivtv: i2c attach [client=MSP3435G-B6,ok]
ivtv: Tuner Type 2, Tuner formats 0x00001000, Radio:
yes, Model 0x00891450, Revision 0x00000000
ivtv: NTSC tuner detected
ivtv: Radio detected
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware may be buggy, use version
0x02040011
ivtv: Configuring WinTV PVR 250 card with 5 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers
 4194304 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers 
2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 455 4608 byte buffers 
2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Setting Tuner 2
tuner 0-0061: type set to 2 (Philips NTSC
(FI1236,FM1236 and compatibles))
saa7115: decoder set input (4)
saa7115: now setting Composite input
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to NTSC.
ivtv: ivtv_enc_thread: pid = 4889, itv = 0xe8b48820
saa7115: decoder set norm NTSC
saa7115: set audio: 0x01
ivtv: Initialized WinTV PVR 250, card #0
ivtv: ====================  END INIT IVTV 
====================
saa7115: decoder disable output
saa7115: decoder enable output
ivtv: ENC: User stopped capture.


--- Nick <knowledgejunkie at gmail.com> wrote:

> On 06/09/05, Vassilis <vassilisv at yahoo.com> wrote:
> > All,
> > 
> > I have been following the instructions on Fedora
> > Myth(TV)ology and I run into a problem while
> loading
> > the ivtv module with a PVR-250 card. I also did an
> > lspci and the card is detected, it looks like an
> > interrupt conflict. Any ideas on how to solve
> this?
> > Logs are attached bellow.
> > 
> 
> Trying moving the card to another PCI slot.
> 
> Nick
> 



	
		
______________________________________________________
Click here to donate to the Hurricane Katrina relief effort.
http://store.yahoo.com/redcross-donate3/