[mythtv-users] winfast tv2000xp no video, green screen

[Eric Becker]

 I have a leadtek winfast tv2000xp tuner card.  I've been following
mythtv howto and the gentoo wiki for setting up mythtv.  I can get video
and audio output from xawtv, but there's no video from mythtv.  I can
use the up and down arrows to change the channel and I can tell
something is working because I can hear the audio switching form channel
to channel, but the screen never changes.  It's just a solid green
screen.

lscpi:
0000:00:0f.0 Multimedia video controller: Brooktree Corporation Bt878
Video Capture (rev 11)
0000:00:0f.1 Multimedia controller: Brooktree Corporation Bt878 Audio
Capture (rev 11)

I am loading the bttv module in /etc/modules.autoload.d/kernel-2.6 with
"bttv card=34 radio=1 tuner=2"

lsmod:
tuner                  36776  0
bttv                  154448  1
video_buf              17636  1 bttv
firmware_class          7744  1 bttv
i2c_algo_bit            8808  1 bttv
v4l2_common             4640  1 bttv
btcx_risc               3912  1 bttv
tveeprom               10384  1 bttv
i2c_core               17328  4 tuner,bttv,i2c_algo_bit ,tveeprom
videodev                7168  2 bttv

dmesg:
Linux video capture interface: v1.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKC] -> GSI 5 (level,
low) -> IRQ 5
bttv0: Bt878 (rev 17) at 0000:00:0f.0, irq: 5, latency: 32, mmio:
0xe7000000
bttv0: detected: Leadtek WinFast TV 2000 [card=34], PCI subsystem ID is
107d:6606
bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,insmod
option]
bttv0: gpio: en=00000000, out=00000000 in=00bf7707 [init]
bttv0: using tuner=2
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found<!--D(["mb","
\r\nbttv0: i2c: checking for TDA7432 @ 0x8a... not found
\r\nbttv0: i2c: checking for TDA9887 @ 0x86... not found
\r\n: chip found @ 0xc2 (bt878 #0 [sw])
\r\ntuner 0-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and
compatibles))
\r\nbttv0: registered device video0
\r\nbttv0: registered device vbi0
\r\nbttv0: registered device radio0
\r\nbttv0: PLL: 28636363 => 35468950 .. ok
\r\nbttv0: add subdevice remote0
\r\nfbsplash: console 1 using theme \'livecd-2005.1\'
\r\nfbsplash: switched splash state to \'on\' on console 1
\r\nfbsplash: console 2 using theme \'livecd-2005.1\'
\r\nfbsplash: switched splash state to \'on\' on console 2
\r\nfbsplash: console 3 using theme \'livecd-2005.1\'
\r\nfbsplash: switched splash state to \'on\' on console 3
\r\nfbsplash: console 4 using theme \'livecd-2005.1\'
\r\nfbsplash: switched splash state to \'on\' on console 4
\r\nfbsplash: console 5 using theme \'livecd-2005.1\'
\r\nfbsplash: switched splash state to \'on\' on console 5
\r\nfbsplash: console 6 using theme \'livecd-2005.1\'
\r\nfbsplash: switched splash state to \'on\' on console 6
\r\nfbsplash: console 7 using theme \'livecd-2005.1\'
\r\nfbsplash: switched splash state to \'on\' on console 7
\r\nfbsplash: console 8 using theme \'livecd-2005.1\'
\r\nfbsplash: switched splash state to \'on\' on console 8
\r\nfbsplash: console 9 using theme \'livecd-2005.1\'
\r\nfbsplash: switched splash state to \'on\' on console 9
\r\nfbsplash: console 10 using theme \'livecd-2005.1\'
\r\nfbsplash: switched splash state to \'on\' on console 10
\r\nACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 5 (level,
low) -> IRQ 5
\r\nPCI: Setting latency timer of device 0000:00:07.5 to 64
\r\neth0: link up, 100Mbps, full-duplex, lpa 0x45E1
\r\nbttv0: PLL can sleep, using XTAL (28636363).
\r\nbttv0: PLL: 28636363 => 35468950 .. ok
\r\nbttv0: PLL can sleep, using XTAL (28636363).
\r\nbttv0: timeout: drop=136 irq=9440/17340, risc=07ed303c, bits: HSYNC
OFLOW
\r\nbttv0: reset, reinitialize
\r\
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
 : chip found @ 0xc2 (bt878 #0 [sw])
tuner 0-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and
compatibles))
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: add subdevice "remote0"
fbsplash: console 1 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 1
fbsplash: console 2 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 2
fbsplash: console 3 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 3
fbsplash: console 4 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 4
fbsplash: console 5 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 5
fbsplash: console 6 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 6
fbsplash: console 7 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 7
fbsplash: console 8 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 8
fbsplash: console 9 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 9
fbsplash: console 10 using theme 'livecd-2005.1'
fbsplash: switched splash state to 'on' on console 10
ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 5 (level,
low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:07.5 to 64
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
bttv0: PLL can sleep, using XTAL (28636363).
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: PLL can sleep, using XTAL (28636363).
bttv0: timeout: drop=136 irq=9440/17340, risc=07ed303c, bits: HSYNC
OFLOW
bttv0: reset, reinitialize
bttv0: PLL can sleep, using XTAL (28636363).<!--D(["mb","
\r\nbttv0: timeout: drop=186 irq=9589/18318, risc=0a3216e4, bits: VSYNC
HSYNC OFLOW
\r\nbttv0: reset, reinitialize
\r\nbttv0: PLL can sleep, using XTAL (28636363).
\r\nbttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
\r\nbttv0: OCERR @ 1c12c014,bits: HSYNC OFLOW OCERR*
\r\nbttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
\r\nbttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
\r\nbttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
\r\nbttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
\r\nbttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
\r\nbttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
\r\nbttv0: OCERR @ 1c12c01c,bits: VSYNC* HSYNC OFLOW OCERR*
\r\nbttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*

\r\n\r\n\r\n\r\
bttv0: timeout: drop=186 irq=9589/18318, risc=0a3216e4, bits: VSYNC
HSYNC OFLOW
bttv0: reset, reinitialize
bttv0: PLL can sleep, using XTAL (28636363).
bttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
bttv0: OCERR @ 1c12c014,bits: HSYNC OFLOW OCERR*
bttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
bttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
bttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
bttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
bttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
bttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*
bttv0: OCERR @ 1c12c01c,bits: VSYNC* HSYNC OFLOW OCERR*
bttv0: OCERR @ 1c12c01c,bits: HSYNC OFLOW OCERR*


-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://mythtv.org/pipermail/mythtv-users/attachments/20051114/34653358/attachment.htm