[mythtv-users] PVR500MCE tuner #1, ivtv: i2c client addr: 0x44 not found for command

Sat Jul 23 06:52:03 EDT 2005

> -----Original Message-----
> From: mythtv-users-bounces at mythtv.org [mailto:mythtv-users-
> bounces at mythtv.org] On Behalf Of of my own
> Sent: Saturday, July 23, 2005 5:37 AM
> To: mythtv-users at mythtv.org
> Subject: [mythtv-users] PVR500MCE tuner #1,ivtv: i2c client addr: 0x44 not
> found for command
> 
> I am using the latest ivtv driver, tuner 0 loaded fine, works on myth,
> but tuner #1 gave the following error below, system is P4 1.8G running
> FC3, any idea? thanks.
> 
> ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
> ivtv: i2c client addr: 0x44 not found for command 0x40046466!
> ivtv: Setup VBI API header 0x0000bd0d pkts 1 buffs 4 ln 24 sz 1456
> ivtv: Setup VBI start 0x002fea04 frames 4 fpi 1 lines 0x00000140
> ivtv: i2c client addr: 0x44 not found for command 0x40046406!
> ivtv: i2c client addr: 0x44 not found for command 0x40046406!
> ivtv: No Free Mailbox for cmd 0x000000c6 after 100 tries!
> ivtv: Mailbox[0] 0x000000dc flags 0x00000003
> ivtv: Mailbox[1] 0x300000c2 flags 0x300000c2
> ivtv: Mailbox[2] 0x300000c2 flags 0x300000c2
> ivtv: Firmware UNRESPONSIVE when trying cmd 0x000000c6!!!
> 
> -------------------------------
> /etc/modprobe.conf
> alias char-major-81 videodev
> alias char-major-81-0 ivtv
> alias char-major-81-1 ivtv
> options cx25480 i2c_enable=-1,1,1
> options saa7127 i2c_enable=1,-1,-1
> 
> ---------------------------------
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.3.7 (a) loading
> ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4
> ivtv: In case of problems please include the debug info
> ivtv: between the START INIT IVTV and END INIT IVTV lines when
> ivtv: mailing the ivtv-devel mailinglist.
> ivtv: Autodetected WinTV PVR 150 card
> ivtv: Found an iTVC16 based chip
> ACPI: PCI interrupt 0000:03:08.0[A] -> GSI 11 (level, low) -> IRQ 11
> ivtv: XXX PCI device: 0x1a30 vendor: 0x8086
> tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926
> tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
> tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
> tveeprom: audio_processor = MSP3410D (type = 5)
> ivtv: i2c attach [client=tveeprom[50],ok]
> tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
> ivtv: i2c attach [client=(tuner unset),ok]
> cx25840: starting probe on adapter ivtv i2c driver #0 (0x10005)
> cx25840: detecting cx25840 client on address 0x88
> cx25840: cx25843-23 found. Initializing...
> cx25840: requesting /lib/modules/HcwMakoA.ROM
> cx25840: firmware loaded
> ivtv: i2c attach [client=cx25840[50],ok]
> ivtv: i2c attach [client=wm8775[50],ok]
> ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model
> 0x00914652, Revision 0x00000001
> ivtv: NTSC tuner detected
> ivtv: Radio detected
> ivtv: Encoder revision: 0x02050032
> ivtv: Encoder Firmware may be buggy, use version 0x02040011
> ivtv: Configuring WinTV PVR 150 card with 5 streams
> ivtv: Registered v4l2 device for encoder MPEG minor 0
> ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder YUV minor 32
> ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder VBI minor 224
> ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder PCM audio minor 24
> ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder radio minor 64
> ivtv: Create encoder radio stream
> ivtv: Setting Tuner 57
> tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0
> cx25840: decoder set norm NTSC
> cx25840: decoder set input (6)
> cx25840: now setting Tuner input
> cx25840: set audio input (0)
> ivtv: Switching standard to NTSC.
> cx25840: decoder set norm NTSC
> ivtv: Initialized WinTV PVR 150, card #0
> ivtv: Autodetected WinTV PVR 150 card
> ivtv: Found an iTVC16 based chip
> ACPI: PCI interrupt 0000:03:09.0[A] -> GSI 10 (level, low) -> IRQ 10
> ivtv: XXX PCI device: 0x1a30 vendor: 0x8086
> tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926
> tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
> tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
> tveeprom: audio_processor = MSP3410D (type = 5)
> ivtv: i2c attach [client=tveeprom[50],ok]
> tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
> ivtv: i2c attach [client=(tuner unset),ok]
> cx25840: starting probe on adapter ivtv i2c driver #1 (0x10005)
> ivtv: i2c attach [client=wm8775[50],ok]
> ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model
> 0x00914652, Revision 0x00000001
> ivtv: Radio detected
> ivtv: ivtv_enc_thread: pid = 5565, itv = 0xe2230d20
> ivtv: ivtv_enc_vbi_thread: pid = 5566, itv = 0xe2230d20
> ivtv: Encoder revision: 0x02050032
> ivtv: Encoder Firmware may be buggy, use version 0x02040011
> ivtv: Configuring WinTV PVR 150 card with 5 streams
> ivtv: Registered v4l2 device for encoder MPEG minor 1
> ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder YUV minor 33
> ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder VBI minor 225
> ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder PCM audio minor 25
> ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
> ivtv: Registered v4l2 device for encoder radio minor 65
> ivtv: Create encoder radio stream
> ivtv: Setting Tuner 57
> tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1
> ivtv: i2c client addr: 0x44 not found for command 0x40046403!
> ivtv: i2c client addr: 0x44 not found for command 0x40046404!
> ivtv: i2c client addr: 0x44 not found for command 0x4004646e!
> ivtv: Switching standard to NTSC.
> ivtv: i2c client addr: 0x44 not found for command 0x40046403!
> ivtv: Initialized WinTV PVR 150, card #1
> ivtv: ====================  END INIT IVTV  ====================
> ivtv: ivtv_enc_thread: pid = 5678, itv = 0xe22542f4
> ivtv: ivtv_enc_vbi_thread: pid = 5679, itv = 0xe22542f4

ivtv: Encoder revision: 0x02050032
ivtv: Encoder Firmware may be buggy, use version 0x02040011

Go here and get the correct firmware
http://ivtv.writeme.ch/tiki-index.php?page=FirmwareVersions

Then try again. I don't have a PVR 500 so not sure it will work, but it
can't hurt to try.