[mythtv-users] lirc_mceusb
Wayne Vosberg
wayne at mindtunnel.com
Fri Dec 10 03:28:55 UTC 2004
Nate Carlson wrote:
> On Thu, 9 Dec 2004, Wayne Vosberg wrote:
>
>> Anyone have any luck with this remote:
>>
>> http://www.newegg.com/app/ViewProductDesc.asp?description=80-100-202&depa=0
>>
>>
>> I've tried both lirc-0.7.0 and 0.7.1. After modifying lirc_mceusb.c
>> for my Product/Vendor ID I can compile and install just fine. Module
>> installs with no complaints and lircd starts just fine (with standard
>> lircd.conf.mceusb in place). But irw never sees a button push and
>> irrecord doesn't either. The receiver LED does flash ....... any ideas?
>
>
> Yeah, I've been using it for a few months; it works great for me.
> Sounds like about the same install you have. Are you getting any
> messages about the remote in dmesg?
>
> Dec 9 12:15:02 chromium kernel: hub.c: new USB device 00:11.2-2,
> assigned address 2
> Dec 9 12:15:02 chromium kernel: usb.c: USB device 2 (vend/prod
> 0x45e/0x6d) is not claimed by any active driver.
> Dec 9 12:15:02 chromium kernel: lirc_dev: IR Remote Control driver
> registered, at major 61
> Dec 9 12:15:02 chromium kernel: usb.c: registered new driver
> ir_transceiver
> Dec 9 12:15:02 chromium kernel: lirc_dev:
> lirc_register_plugin:sample_rate: 80
> Dec 9 12:15:02 chromium kernel: lirc_mceusb.c: USB Microsoft IR
> Transceiver Driver v0.2
>
> ------------------------------------------------------------------------
> | nate carlson | natecars at natecarlson.com | http://www.natecarlson.com |
> | depriving some poor village of its idiot since 1981 |
> ------------------------------------------------------------------------
>
>------------------------------------------------------------------------
>
>_______________________________________________
>mythtv-users mailing list
>mythtv-users at mythtv.org
>http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
>
>
on plugging in the receiver I get:
Dec 9 20:18:56 gypsy kernel: lirc_dev: IR Remote Control driver
registered, at major 61
Dec 9 20:18:56 gypsy kernel: lirc_dev: lirc_register_plugin:sample_rate: 80
Dec 9 20:18:56 gypsy kernel: usbcore: registered new driver lirc_mceusb
Dec 9 20:18:56 gypsy kernel:
/root/drivers/lirc/drivers/lirc_mceusb/lirc_mceusb.c: USB Microsoft IR
Transceiver Driver v0.2
In dmesg I see:
usb 3-1: new full speed USB device using address 5
usb 3-1: device not accepting address 5, error -71
usb 3-1: new full speed USB device using address 6
floppy0: no floppy controllers found
lirc_dev: IR Remote Control driver registered, at major 61
lirc_dev: lirc_register_plugin:sample_rate: 80
usbcore: registered new driver lirc_mceusb
/root/drivers/lirc/drivers/lirc_mceusb/lirc_mceusb.c: USB Microsoft IR
Transceiver Driver v0.2
If I modprobe with debug=1 I get:
/root/drivers/lirc/drivers/lirc_mceusb/lirc_mceusb.c: we found a bulk
out endpoint
/root/drivers/lirc/drivers/lirc_mceusb/lirc_mceusb.c: we found a bulk in
endpoint
lirc_dev: lirc_register_plugin:sample_rate: 80
/root/drivers/lirc/drivers/lirc_mceusb/lirc_mceusb.c: mceusb_setup - res
= 2 status = 0x1 0x0
/root/drivers/lirc/drivers/lirc_mceusb/lirc_mceusb.c: mceusb_setup - res
= -32, devnum = 6
/root/drivers/lirc/drivers/lirc_mceusb/lirc_mceusb.c: mceusb_setup -
data[0] = 0, data[1] = 0
/root/drivers/lirc/drivers/lirc_mceusb/lirc_mceusb.c: mceusb_setup - res
= -32
usbcore: registered new driver lirc_mceusb
/root/drivers/lirc/drivers/lirc_mceusb/lirc_mceusb.c: USB Microsoft IR
Transceiver Driver v0.2
I also see occasional 'bulk timeout on ep1in' messages.
Note - my remote is a generic philips usb/mce: Bus 003 Device 006: ID
0471:0815 Philips
45e/6d are the vendor/product ID's hardcoded in the driver --- do you
have a part number
for you remote?
Note - I've tried this on FC2 (2.6.9-1.6_FC2smp) and FC3
(2.6.9-1.681_FC3.stk16) with
both lirc 0.7.0 and latest cvs (0.7.1) with the same results.
More information about the mythtv-users
mailing list